Guide (New 2022) Actual VMware 2V0-41.20 Exam Questions
2V0-41.20 Exam Dumps Pass with Updated 2022 Certified Exam Questions
VMware 2V0-41.20 Exam Certification Details:
| Recommended Training / Books | VMware NSX-T Data Center: Install, Configure, Manage [V3.0] |
| Exam Code | 2V0-41.20 |
| Schedule Exam | PEARSON VUE |
| Exam Name | Professional VMware NSX-T Data Center (VCP-NV 2021) |
| Duration | 135 minutes |
| Exam Price | $250 USD |
| Sample Questions | VMware 2V0-41.20 Sample Questions |
NEW QUESTION 17
Which three services are compatible with VRF Lite? (Choose three.)
- A. NAT
- B. Intrusion Detection
- C. VPN
- D. Load Balancer
- E. DHCP
Answer: A,B,E
Explanation:
Explanation
VRF Lite is not compatible with the following services:
-VPN
-Load Balancer
Taken from NSX-T ICM 3.0 Lecture Manual.
NEW QUESTION 18
An NSX administrator is reviewing syslog and notices that Distributed Firewall Rules hit counts are not being logged. What could cause this issue?
- A. Zero Trust Security is not enabled
- B. Distributed Firewall Rule logging is not enabled
- C. Syslog is not configured on the NSX Manager
- D. Syslog is not configured on the ESXi transport node
Answer: B
NEW QUESTION 19
Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?
- A. set support-bundle file vcpnv.tgz
- B. vm-support
- C. get support-bundle file vcpnv.tgz
- D. esxcli system syslog config logger set --id=nsxmanager
Answer: B
NEW QUESTION 20
Which network tool cloud an administrator use on an ESXi 7 host to capture packets when troubleshooting connectivity issues?
- A. net-stats
- B. tcpdump
- C. Wireshark
- D. pktcap-uw
Answer: D
Explanation:
If you do when troubleshooting connectivity issues on your Virtualization environment. This post will help you to capture Network traffic on ESXi host using pktcap-uw tool.
NEW QUESTION 21
An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600.
Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?
- A. esxcli network diag ping -H <destination IP address>
- B. vmkping ++netstack=vxlan-d -s 1572 <destination IP address>
- C. vmkping ++netstack=geneve -d -s 1572 <destination IP address>
- D. esxcli network diag ping -I vmk0 -H <destination IP address>
Answer: B
NEW QUESTION 22
What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN- backed logical switch?
- A. Downlink interface
- B. Service interface
- C. VLAN Uplink
"The service interface is a special-purpose port to enable services for mainly VLAN-based networks. North-south service insertion is another use case that requires a service interface to connect a partner appliance and redirect north-south traffic for partner services. Service interfaces are supported on both active-standby Tier-0 logical routers and Tier-1 routers. Firewall, NAT, and VPNs are supported on this interface. The service interface is also a downlink" - D. Loopback Router Port
Answer: B
NEW QUESTION 23
A customer has a network where BGP has been enabled and the BGP neighbor is configured on the Tier-0 Gateway. A NSX-T Data Center administrator used the get logical-routers command to retrieve this information:
Which two commands must be executed to check BGP neighbor status? (Choose two.)
- A. sa-nsxedge-01(tier0_sr)> get bgp neighbor
- B. sa-nsxedge-01(tier0_dr)> get bgp neighbor
- C. sa-nsxedge-01(tier1_sr)> get bgp neighbor
- D. vrf 1
- E. vrf 3
- F. vrf 4
Answer: A,E
NEW QUESTION 24
Which tool could be used to configure BGP on a Tier-0 Gateway?
- A. API
- B. ESX CLI
- C. PowerShell
- D. NSX CLI
Answer: D
NEW QUESTION 25
An NSX administrator has configured a KVM hypervisor as a transport node.
Which kernel module on KVM implements a N-VDS?
- A. dvswitch
- B. nsx-vswitch
- C. etherswitch
- D. openvswitch
Answer: D
NEW QUESTION 26
Which is correct when deploying a NSX Edge in a KVM only environment?
- A. deploy NSX Edge on a bare-metal server
- B. deploy NSX Edge VM with ISO image
- C. deploy NSX Edge VM with OVF template
- D. deploy NSX Edge VM with QCOW2 image
Answer: A
NEW QUESTION 27
What are the advantages of using a Tier-0 Gateway in ECMP mode? (Choose two.)
- A. increased north/south bandwidth
From ICM manual:
Equal-cost multipath (ECMP) routing has several features and functions:
* ECMP routing increases the north-south communication bandwidth by combining multiple uplinks.
* ECMP routing performs traffic load balancing.
* ECMP routing provides fault tolerance for failed paths.
* A maximum of eight ECMP paths are supported.
* Hashing is based on 2-tuple IP source and destination addresses.
* ECMP routing is only available on Tier-0 gateways. - B. stateful services leveraged
- C. traffic predictability
- D. traffic load balancing
- E. Failover of services
Answer: A,D
NEW QUESTION 28
Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.)
- A. Multicast is supported in ESXi and KVM transport nodes.
- B. An Edge can be the Rendezvous Point.
- C. Multicast routing is implemented with PIM Sparse-Mode.
- D. IGMP Snooping is used to populate multicast forwarding tables.
- E. Tier-0 gateways can be the Rendezvous Point.
Answer: C,D
Explanation:
Explanation
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/nsxt_30_admin.pdf
NEW QUESTION 29
Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?
- A. ipconfig
- B. tcpdump
- C. ifconfig
- D. debug
Answer: C
Explanation:
Explanation
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/installation/GUID-B7E7371E-A9F6-4880-B184-
NEW QUESTION 30
An NSX administrator is creating a NAT rule on a Tier-0 Gateway configured in active-standby high availability mode.
Which two NAT rule types are supported for this configuration? (Choose two.)
- A. Destination NAT
- B. 1:1 NAT
- C. Source NAT
- D. Port NAT
- E. Reflexive NAT
Answer: A,C
NEW QUESTION 31
Which tool could be used to inspect the path of a packet in the data plane?
- A. Port Connection
- B. Netflow
- C. Port Mirroring Session
- D. Traceflow
Answer: D
NEW QUESTION 32
Which three can an administrator define in a transport node profile? (Choose three.)
- A. Uplink Profile
- B. Segment Profile
- C. Logical Router
- D. N-VDS switch configuration
- E. Segment
- F. VDS switch configuration
Answer: A,D,F
NEW QUESTION 33
Which CLI command on NSX Manager and NSX Edge is used to change NTP settings?
- A. set timezone
- B. set ntp-server
- C. et time-server
- D. get timezone
Answer: B
NEW QUESTION 34
An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.
Which CLI command disables the nsxcli time out value on NSX Manager?
- A. set cli-timeout disabled
- B. set cli-timeout enabled
- C. set cli-timeout 0
- D. set cli-timeout 1
Answer: C
Explanation:
Reference:
" https://vdc-download.vmware.com/vmwb-repository/dcr-public/cc42e3c1-eb34-4567-a916-147e79798957/8264605c-a5e1-49a8-b603-cc78621eeeab/cli.html#set%20cli-timeout%20%3Ctimeout%3E
https://www.virten.net/2020/06/quick-tip-remove-nsx-t-ssh-and-http-session-timeout/
NEW QUESTION 35
An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events.
Which message ID (msgid) should be used in the syslog export configuration command as a filter?
- A. GROUPING
- B. MONITORING
- C. FABRIC
- D. SYSTEM
Answer: C
Explanation:
Reference:
https://docs.vmware.com/en/VMware-NSX-T-Data-Center/3.0/nsxt_30_admin.pdf
NEW QUESTION 36
Which two ports are used by a transport node to communicate with the management and control planes in NSX-T Data Center 3.0? (Choose two.)
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: A,C
Explanation:
Explanation
The NSX Manager management plane communicates with the transport nodes by using APH Server over NSX-RPC/TCP through port 1234. CCP communicates with the transport nodes by using APH Server over NSX-RPC/TCP through port 1235. Taken from NSX-T ICM 3.0 Lecture manual
NEW QUESTION 37
An NSX administrator has observed connectivity issues between the NSX Manager and the KVM Transport Node.
Which two log files could be used to troubleshoot the issue on the KVM Transport Node? (Choose two.)
- A. /usr/vmware/log/syslog
- B. /var/log/syslog
- C. /var/log/nsx/syslog
- D. /var/log/vmware/nsx-syslog
- E. /usr/vmware/nsx-syslog
Answer: B,D
NEW QUESTION 38
An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600.
Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?
- A. esxcli network diag ping -H <destination IP address>
- B. vmkping ++netstack=vxlan-d -s 1572 <destination IP address>
- C. vmkping ++netstack=geneve -d -s 1572 <destination IP address>
- D. esxcli network diag ping -I vmk0 -H <destination IP address>
Answer: B
Explanation:
Explanation
https://kb.vmware.com/s/article/1003728
NEW QUESTION 39
......
Pass Guaranteed Quiz 2022 Realistic Verified Free VMware: https://studyguide.pdfdumps.com/2V0-41.20-valid-exam.html